Hot Sale Products

light bar with axial adjustability

by:Marslite     2019-10-13
I made a light bar for my new 160 square feet. art studio.
This is a DJ truss with vanity light bars, and the novel project is to build a clip to connect these parts.
Easy to grasp: 1.
Size of cut 4x42.
Drill through the middle of 4x4 3.
Tear the boring 4x4 portrait.
Connect the result to the tubular structure.
Wire clip limit 1.
After installation, the axial resistance is not easy to adjust.
The nature of the material needs careful management. g.
In order to avoid wood splitting, the resistance of the clip should be set. Pliers benefits1.
The smallest pronunciation.
The flood light bulb is heavier, with 8 vanity pads each, and weight management is required.
Part of the reason for choosing not to use extra hardware is to keep the load as tight as possible.
Settings can be modified for more adaptability (
Additional advertising agents)
, But sacrificed the extra pressure on the 4x4 fixture.
6x6 can realize the setting of more bullet proof clothes.
The scale of the design is another project. 2.
Clamp and load balancing.
This encourages multiple working spaces.
Even for a separate work space, the lights in the opposite direction provide an indirect atmosphere.
System benefits: 1. Simplicity. 2. Minimal cost.
The biggest upfront cost is the key structure: Truss, lamp, socket.
The cost of all wood is about $20 and has achieved very good results compared to the metal connection system.
The vanity fixture was selected as pre-
Fab of something that takes a lot of time to invest in order to copy manually to get a negligible mechanical advantage.
I was hoping that the E26 socket would adhere better to the sheet metal backing, but the imperfect socket adhesion is ultimately negligible.
Although the truss frame is expensive, any similar frame setting is the same or more expensive.
LED bulbs are really stealing things.
Thanks to the subsidized sales as of December 31, 2014, all bulbs were purchased from Aubuchon Hardware store in Vermont for $5 each.
One note on the absent drill press: 4 x 4S drilling does not need to be perfect.
However, it is appropriate to use a drill press. Cost:$120 -(4)8-
$160-socket Vanity Fixtures(32)
LED floodlights $130-
$20-10\' DJ truss
Wood One unprocessed pine Wood ~ 8\' long x 9\' wide x 3/4 \'deep 1 untreated 4x4, 8 \'(only 26.
25 \"used in final product\"$20 -
Extension Line in store $30-
Electrical wiring and multiple
$30-Click Connect Rig
Steel saw removing material from Truss $5-
$10-1/2 \"shovel drill
$5-1/8 long drill
Electrical terminals connected to the switch wiring = $530 plus taxes, time, gas, incidentals and other materials for use directly: Bench cordless hand drill, in particular, a frying saw modified for drilling 1 1/2 of the hole, various wood screws and sheet metal ironing plates, used as a table saw or frying saw
Wood used to guide/push the woodworking gripper to smooth any cut material workshop vacuum cleaner/tape measuring speed square2B and 4B pencils is best suited to Mark woodworking grinding wheels to shorten the drill bit from retail gloves with a length of 1/8, goggles, ear protection, particle face maskBother P-
Touch-type electrical switch glue gun for fixing the switch on the clamp for clamping the clamp on the clamp terminal (
Why does every retail ginning have a Prop 65 warning? )
Cable tie band for wiringWire nuts for cutting wirecct tape for covering the electrical or rough points of the cable. Prepare the truss to assemble the Truss before doing anything.
The truss consists of two pieces, connected in the middle and supported by two tripod.
Label each corner of the two truss pieces.
The model of this truss allows the removal of 6 with a hacksaw.
0 cm from the inside, 1.
Relax 0 cm from the side of each tubular piece.
This is to extend the tripod base more fully with room size limitations. The T-braces (
Hardware for vertical connection of tubular frames)
Only partial disassembly of the truss can be modified.
By letting T-
Starting with the initial assembly, it is relatively easy to install the modified truss.
Prepare vanity fixtures from retail packaging, each with a chrome-plated valve and stabilizer.
Remove a single useful part, connect to the metal sheet on eight E26 ceramic sockets and remove the ground jointdown.
Note: Due to the single point installation of each ceramic socket, the rotation of the mechanical support of the fixture is less than 180 degrees.
This means that the 180 degree rotation of the barrier-free can make the load self-destructively.
The sheet metal size of the vanity fixture for the ready support plate is about 43 3/4 \"long x 4\" wide.
Take a pine board with an approximate actual size of 8\' long x 9\' wide x 3/4 \'deep, quarterly it, and produce 4 boards with a length of x 4.
5 \"wide x 3/4\" deep.
Stabilize each dresser with a board;
It also provides a method for manual angle adjustment.
Cut 4x4 pieces to measure the triangular truss support element vertically to determine the allowable length of the 4x4 fixture;
6 \"is enough.
Multi-segment measurement cutting; I cut eight.
Mark each end of each segment from angle to angle and make \"X\" to drill holes in the center.
Use 2B or 4B pencils from the art store: graphite is softer and easier to release.
Through the center drilling of each 4x4 part, you can use 1 1/2 shovel bit and wired hand drill.
In this way, drill from one side to the other.
Reasonable accuracy produces good results.
Explain the error with hand drill and reduce additional inventory.
The drilling machine with hole saw is ideal, but this precision is not required for the intended tolerance of the system.
Please note: the drilling effect from both ends to the middle is poor.
Manual drilling from one end to the other is not technically obvious, but: 1. )
Each 4x4 clip uses only one side and two side. )
The material is tolerant.
Therefore, there are no mechanical shortcomings in the hand drill, and the technical imperfections can be ignored (
And may help with axial resistance. . . [a good thing. . . ]).
Mark each set of fixtures with a permanent mark to identify if they are suitable for installation.
Tear each boring 4x4 part in half with a table saw to produce two combined clamps.
Drill through two and a half to prepare for the flap. Using the drilling machine, the procedure for this step is simpler.
Use a hand drill and take the following
Steps to ensure that the clamping screws are installed in the center straight holes of each clamping base.
Using a drill bit 1/8 long can compensate for the inaccuracy of manual drilling.
If you get 12 \"1/8 long\" bits from the store, just cut and grind to about 5-
6 \"reduce the error. 1.
Measure the drilling point of each base of a fixture.
No need to measure the second fixture. 2.
Drill from the center side of the fixture to the outside. 3.
Fix the 4x4 clamping half together with a woodworking fixture, and use a 1/8 long drill bit to follow the drilling just made and complete the straight line by 4x4 clamping half. 4.
Finally, with a larger (1/2\")
Drill bit, tilt the edge of each 1/8 \"drill hole, so each 3\" drywall screw will flush and recessed to allow the installation of the dresser and its support plate.
Fix the 4x4 fixture on the truss: 1.
Place the first half of each fixture group on the working surface.
Place the truss in the desired fit position. 2.
Place the second half of the clip in place. 3.
Before fixing the first screw, use 4-
There are 5 stacked washers on the suggested side.
When approaching a level, prefer a closer gap rather than a wider gap. 4.
Insert the first screw fairly tight. 5.
Remove the gasket.
Note: keeping the gasket above this will reduce/eliminate axial tension.
On the other hand, not using anything to adjust the level of the fixture can cause the fixture to be poorly arranged and/or broken.
Use props (the washers)
For a single screw, the fixture will maintain most of the level when inserting other screws and bend enough to provide proper axial tension. 6.
Gently insert the remaining screws and tighten them properly to feel tension.
Please release some screws if the tension is too large.
If there is not enough tension, either add more screws to the intermediate material or remove all screws and start over.
For stability, the support plate should be installed on the board.
Center the support plate and install it on the surface of both fixtures.
Use 1 drywall screw of 1/4.
The soft wood does not need a slope edge.
Due to the thickness of the material, you can drill holes close to the middle of the fixture.
Insert the screw so that it is flush with the material as the vanity bar will be mounted on the top.
Board the dresser Bar and The Dresser bar. Use 2-
4 sheet metal screws per lamp holder.
Wire itCut home extension cord to get the wire with socket pins.
Connect the wire using the wire nut.
You can pin the gun on the 4x4 clip;
The cable connects the rest to the truss frame.
Add the switch to the system by mounting the switch to a short segment of the 4x4 fixture.
Insert a standard pin into multiple pins
Click on the final installation.
Attach in the picture how the truss bolt assembly adds a series of truss fragments of washers. By sawing 6.
0 cm from the middle part of the four steel pipes, the structure is assembled together with the flying screw cap inside the truss support beam, making the stock Bolt too long.
Use more washers to solve cheap and easy problems.
Interestingly, the stock hole of the tubular frame perfectly adapts to the length modification.
Install the assembled truss on the tripdsuse. Use extension lines to help more
Click to reach the wall outlet.
Cable ties any slack.
Install the floodlight and light it up.
The clamping mechanism can be used with a tripod or torchiere floor lamp.
Before this project, I modified a couple of tochière, which received bright light, but only from a single vertical light source, such as stadium lighting that produced many shadows.
A major drawback is the stability of the bracket, which can be improved with a tripod base.
Drill borer of different width can hold different objects.
Recall the circumference = (pi)Diameter2.
The $530 light rig is a bit expensive, but it will take about $16 if it is removed.
56 fixed bulbs each on a sturdy and portable frame.
When you go skiing in Vermont, check out the light bulb sales! 3.
My building can be adjusted about 84 degrees in the horizontal direction, 42 degrees in each direction.
Downward/upward illumination can be achieved by adjusting the size of the balance block through truss support.
Alternatively, some support beams can be removed while maintaining structural integrity. 4.
This is a good light therapy tool.
Compared to residential and commercial environments with sparse/dim/poor lighting, objects and colors in the room are displayed very clearly in this setting.
I\'m not sure about the output of UV rays or the production of vitamins, but when things look bright, certain parts of the brain say the sun is coming out.
I am very satisfied with this building and hope you like it!
Custom message
Chat Online 编辑模式下无法使用
Chat Online inputting...